Prodott
MM10 Series ODM Peristaltic Pump
Deskrizzjoni Qasira:
Firxa tal-fluss：≤144ml/min
Numru massimu ta 'kanali：1
Ibgħat Email Lilna
■Lead Fluid MM10 pump head suitable for wall thickness 0.8-0.92mm, ID 0.13-3.2mm Silicone, Pharmed, PVC, Viton etc. tubu tal-materjal, it can run continuously at the max flow rate 36 ml/min at 100 rpm, and interval operation the max speed can reach 400 rpm and the flow rate can reach 144ml/min.
■The pump head is made of high-performance plastic material, with high rigidity and strength, and excellent wear resistance.
■The pump head adopts a unique rotary card design. It can be disassembled and assembled without tools. It is easy to replace the pump tube and clean up and maintain. There are two ways to install tube, one is tube connector built-in and the other is to install whole tube.
■Fast-loading pump head, the inlet and outlet end can be installed in any direction on the upper, down and side to meet the needs of different working conditions.
■Matching 12V/24V DC gear motor, stepper motor and other micro-motors.
■Small size, convenient installation and simple operation.
■ It is suitable for supporting various small instruments and equipment to meet the needs of micro-injection, flushing, and drainage.
Material
| Qoxra | Pc |
| Romblu | PET |
Flow Rate Parameter
Materjal tat-tubu：Silikonju, Pharmed, PVC, Viton Wall thickness0.8-0.92mm
| ID（mm) | 0.25 | 0.5 | 1 | 1.52 | 2 | 2.4 | 3.2 | |
| mL/rpm | 0.002 | 0.014 | 0.037 | 0.1 | 0.148 | 0.23 | 0.36 | |
| mL/min (continuous working max100rpm) | 0.17 | 1.4 | 3.7 | 10 | 15 | 23 | 36 | |
| mL/min ( interval working max 400rpm) | 0.68 | 5.6 | 14.8 | 40 | 60 | 92 | 144 | |
★ Above flow parameters are obtained by using silicone tube to transfer pure water under normal temperature and pressure, fl-użu fil-fatt huwa effettwat minn fatturi speċifiċi bħall-pressjoni, medju eċċ. Hawn fuq għal referenza biss
Specifications
| Kanal | 1 |
| Romblu | 3 |
| Firxa tal-fluss | ≤144ml/min |
| Veloċità | continuous working ≤100rpm |
| interval working ≤400rpm(Please confirm with Lead Fluid engineer in advance) | |
| Metodu tat-tubi | Tube connector built-in(ID ≥1.6mm) |
| Whole Tube | |
| Aġġustament tal-clearance | Spazju fiss |
| Mutur | 12V/24V DC gear motor/stepper motor |
| Pressjoni tat-trasmissjoni | ≤0.10MPa |
| Working temperature | 0~40℃ |
| Power | ＜10W |
Speċifikazzjoni tal-Mutur
| DC brush motor | Veloċità：35rpm, 50rpm, 100rpm, 130rpm, 178rpm, 200rpm, 320rpm, 409rpm |
| Voltage：DC12V/3W, DC24V/3W | |
| Preċiżjoni tal-veloċità： ≤ ± 10% | |
| Service life：1000 sigħat |
| DC brushless motor | Veloċità：45rpm, 68rpm, 120rpm, 150rpm, 250rpm, 350rpm |
| Voltage：DC12V/3W, DC24V/3W | |
| Veloċità ：≤ ± 10% |
| 20 Steppes Motor | Motor parameter: step angle 1.8° \ phase 2 \ phase voltage3.9V \ phase current 0.6A \phase resistance 6.5Ω±10% \ phase inductor 2.2mH±20% |
| Firxa tal-veloċità: ≤200rpm |
Dimensjoni (DC gear motor）
Dimensjoni (20 Steppes Motor)
